china s6 imei

Hello need help solve china s6 imei repaiar pb.

Operation : Repair Security [ v1.40 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 24 ]
Sync…
Inital regs read done
Boot Info :
BB_CPU_ID : 6575
BB_CPU_HW : CB00
BB_CPU_SW : 8B00
BB_CPU_SB : E201
BB_CPU_NM : [MediaTek] MT6575|MT6577_S00
Processing BROM stage
i2c Init : 0300771F
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x0F
WD Disable stat : 0x0000
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
DA Stat : v3.2 on BBID : 0x84
DA Sent. Configure setting now …
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0087 , [Micron] MT29C4G96MAZAPCJA_5IT
[NAND] : FLASH_DIE : 002C 00BC 0090 0055 0056 0000 0000
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/01
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

NAND Flash not supported yet in that mode!

Done!
Elapsed: 00:00:19
Reconnect Power/Cable!

Operation : Repair Security [ v1.40 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 24 ]
Sync…
Init Ok, waiting for phone …
Reading initial info, wait…
Phone Info :
Security Info :
IMEI [1] : Damaged!
IMEI [2] : Damaged or not exists
Read Ok!
Update IMEI[1] to : 358236060221304 failed , record not exist or NVRAM damaged!

Done!
Elapsed: 00:05:05
Reconnect Power/Cable!

Operation : Write NVRAM [ v1.40 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 24 ]
Sync…
Inital regs read done
Boot Info :
BB_CPU_ID : 6575
BB_CPU_HW : CB00
BB_CPU_SW : 8B00
BB_CPU_SB : E201
BB_CPU_NM : [MediaTek] MT6575|MT6577_S00
Processing BROM stage
i2c Init : 0300771F
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x0F
WD Disable stat : 0x0000
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
DA Stat : v3.2 on BBID : 0x84
DA Sent. Configure setting now …
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0087 , [Micron] MT29C4G96MAZAPCJA_5IT
[NAND] : FLASH_DIE : 002C 00BC 0090 0055 0056 0000 0000
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/01
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Not supported FlashType yet for this operation !!!

Done!
Elapsed: 00:00:13
Reconnect Power/Cable

Thanks