I9300 after successfull direct emmc jtag cannot flash

the phone had bootloop on samsung logo and when try to flashing it failed and cannot enter recovery mode

I repaired it with direct emmc and there is the log

Z3X EasyJtag Software ver. 2.0.7.3
Loading eMMC Addon Firmware… IO: 2800 mV
Box S/N: 0100F01C69359586, ,FW Ver.: 01.52
CMD Pullup Level:752 mV
CMD Active Level:1588 mV
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 15010056545530304DF781C33C523004

EMMC CSD : D02701320F5903FFF6DBFFFF8E406008

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 03/2013 Rev.0xF7
EMMC NAME: <b>VTU00M</b> , S/N: 2177055826
EMMC NAME (HEX): 56545530304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: <b>Yes<b>
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00

Backup saved: VTU00M_2177055826_20160214_2124.extcsd
Done.

Running:SAMSUNG: MoviNAND Factory Reset…
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1588 mV
Sending Smart Wipe Request…
Wiping Card… Please do not touch it!
<font color="red">Please don’t forget to repair extCSD from backup!</font>
Done.

Running:SAMSUNG: MoviNAND Reset + Format…
Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1588 mV
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Sending Internal Reconfiguration Request…
Waiting configuration Apply!
Restoring configuration…
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Wiping Card… Please do not touch it!
<font color="red">Please don’t forget to repair extCSD from backup!</font>
Done.

Running:Repair extCSD…
Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1588 mV
Writing…
Done.

Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
USB Open Failed, Reason: PORT Open Error
Done.

Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1588 mV
Input file : D:\Firmware\Samsung\Firmware\GT-I9300 Galaxy S3\jtag\EMMC_ROM2_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 …ROM2 (BOOT1 ROM)
Write Block Failed, Reason: Write Block Verify Error
Done.

Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1588 mV
Input file : D:\Firmware\Samsung\Firmware\GT-I9300 Galaxy S3\jtag\EMMC_ROM2_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 …ROM2 (BOOT1 ROM)
Write Block Failed, Reason: Write Block Verify Error
Done.

Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1588 mV
Input file : D:\Firmware\Samsung\Firmware\GT-I9300 Galaxy S3\jtag\EMMC_ROM2_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 …ROM2 (BOOT1 ROM)
Write Block Failed, Reason: Write Block Verify Error
Done.

Z3X EasyJtag Software ver. 2.0.7.3
Loading eMMC Addon Firmware… IO: 2800 mV
Box S/N: 0100F01C69359586, ,FW Ver.: 01.52
CMD Pullup Level:814 mV
CMD Active Level:2268 mV
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 15010056545530304DF781C33C523004

EMMC CSD : D02701320F5903FFF6DBFFFF8E406008

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 03/2013 Rev.0xF7
EMMC NAME: <b>VTU00M</b> , S/N: 2177055826
EMMC NAME (HEX): 56545530304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: <b>Yes<b>
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00

Backup saved: VTU00M_2177055826_20160214_2130.extcsd
Done.

Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2268 mV
Input file : D:\Firmware\Samsung\Firmware\GT-I9300 Galaxy S3\jtag\EMMC_ROM1_00000000_20000000.bin
Writing 0020000000 bytes to 00000000 …ROM1 (USER ROM)
Write Block Failed, Reason: Write Block Verify Error
Done.

Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2268 mV
Input file : D:\Firmware\Samsung\Firmware\GT-I9300 Galaxy S3\jtag\EMMC_ROM2_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 …ROM2 (BOOT1 ROM)
Write Block Failed, Reason: Write Block Verify Error
Done.

Running:SAMSUNG: Remove Write Protection…
Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2268 mV
Removing write protection…
Done.

Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2268 mV
Input file : D:\Firmware\Samsung\Firmware\GT-I9300 Galaxy S3\jtag\EMMC_ROM1_00000000_20000000.bin
Writing 0020000000 bytes to 00000000 …ROM1 (USER ROM)
Done. Write Speed: 6270 kB/s

Z3X EasyJtag Software ver. 2.0.7.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2268 mV
Input file : D:\Firmware\Samsung\Firmware\GT-I9300 Galaxy S3\jtag\EMMC_ROM2_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 …ROM2 (BOOT1 ROM)
Done. Write Speed: 1168 kB/s

After that it is not boot in download mode without SD repair card and then when try to flash it with full rom with pit file it failed

is that mean emmc fault ?