mt 6572 not supported


Card found : S/N : CFEB816C , v0129
Chinese Miracle II [MTK module] v 1.40

Operation : Check / Read Info [ v1.40 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 3 ]
Sync…
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8C00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00C800F4000000000000000000000000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now …
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x009F , [Gigadevice] GD5F4GQ4UAYIG
[NAND] : FLASH_DIE : 00C8 00F4 0000 0000 0000 0001 0BC7
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/00/NIM_Px-2
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Info read not done 🙁 Erased phone or unsupported FlashIc?
You can change settings : Settings -> Other -> NAND init Mode

Done!
Elapsed: 00:00:11
Reconnect Power/Cable!

Operation : Remove Viruses [SmartAV] [ v1.40 ]
SmartAV Conf : 100/80/2000

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 3 ]
Sync…
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8C00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00C800F4000000000000000000000000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now …
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x009F , [Gigadevice] GD5F4GQ4UAYIG
[NAND] : FLASH_DIE : 00C8 00F4 0000 0000 0000 0001 0BC7
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/00/NIM_Px-2
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

NAND Flash not supported yet!

Done!
Elapsed: 00:00:07
Reconnect Power/Cable!

🙁