Mtk-6735 gionee f-103 dead recover


gionee f103 (MTK-6735)dead recover
1st read full factory file from working phone

READ FF

Code:

Operation : Read Flash [ v1.40 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 28 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6735
BB_CPU_HW : CA00
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6735_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 510001154D333238047300425F38E2E0
DA Stat : v4.2 on BBID : 0x93
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM328
[eMMC] : FLASH_CID : 150100513832334D42007304E0E2A25F
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB
INT RAM    : 0x00020000
EXT RAM    : 0x80000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ...

Brand    : GiONEE
ProdName  : F103
ProdModel : F103
Device    : GiONEE_GBL7319
AndroidVer: 5.0
MTKxCPU  : MT6735
MTKxPRJ  : GBL7325GI_0203_T5531

MediaTek MT67xx [x64] : Normalize settings Ok

[Read Ok] : preloader_gionee6735_65c_l.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : logo.bin
[Read Ok] : secro.img
[Read Ok] : tz1.img
[Read Ok] : tz2.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img

[ScatCFG] : MT6735 / V1.1.2 / gionee6735_65c_l / EMMC
FW Size : 2420 MiB
Scatter saved to : C:\InfinityBox\CM2MTK\Flash\MT6735__GiONEE__F103__GiONEE_GBL7319__5.0__GBL7325GI_0203_T5531\

All done!

Done!
Elapsed: 00:07:45
Reconnect Power/Cable!


WRITE FLASH TO FAULTY PHONE
FLASH

Code:


Operation : Flash [ v1.40 ]

======= Flash
Nothing to flash! Select file first!

Scatter Load Ok , BaseBand : MT6735 , Project : gionee6735_65c_l , Storage : EMMC
Files found : 11 , Set to Flash : 10
Ready to Flash!

Operation : Flash [ v1.40 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 28 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6735
BB_CPU_HW : CA00
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6735_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 510001154D333238F1460042A529A5D8
DA Stat : v4.2 on BBID : 0x93
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM328
[eMMC] : FLASH_CID : 150100513832334D420046F1D8A572A5
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB
INT RAM    : 0x00020000
EXT RAM    : 0x80000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6735 , Project : gionee6735_65c_l , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify :  Enabled
Setting : HW verify :  Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 4112 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001C80000-0x0000000004D80000
Erase : 0x0000000006B00000-0x000000039C280000
Flash Pre-Erase Done, time used : 00:00:14

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_gionee6735_65c_l.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0016
Update PMT by user request
Repartition Done!

Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : TEE1
Image Flash Ok
Flash now : TEE2
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:06:27

Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : SECRO
Verify Passed : TEE1
Verify Passed : TEE2
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:00:17

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:07:17
Reconnect Power/Cable!


NOW PHONE ALIVE AND WORKING FINE
THNKS TO INFINITY TEAM

Related: