N8000 After Emmc repair Dead

Actual condition of tab was not able to delete any data so i tried emmc repair here is my logs

Z3X EasyJtag Software ver. 2.3.0.0

Loading eMMC Addon Firmware… IO: 2800 mV
Box S/N: 1212F6161xxxxxxx, ,FW Ver.: 01.55
CMD Pullup Level:1144 mV
CMD Active Level:2134 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower mode is off!
———- eMMC Device Information ———-

EMMC CID : 1501003030303030305620110726589C

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: <b>000000</b> , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]

Partitioning Support [PARTITIONING_SUPPORT]: 0x03

Device support partitioning feature

Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

———————————————

Backup saved: 000000_ 537986854_20160811_1451.extcsd
Done.

Running:SAMSUNG: MoviNAND Factory Reset…
Skip loading eMMC Addon Firmware
CMD Pullup Level:1144 mV
CMD Active Level:2134 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
Sending Smart Wipe Request…
Wiping Card… Please do not touch it!
<font color="red">Please don’t forget to repair extCSD from backup!</font>
Done.

Z3X EasyJtag Software ver. 2.3.0.0

Loading eMMC Addon Firmware… IO: 2800 mV
Box S/N: 1212F61616CBDA85, ,FW Ver.: 01.55
CMD Pullup Level:1144 mV
CMD Active Level:2237 mV
Box IO Level:2800 mV
CLK Rate:140000 khz
Setup firmware update mode, wait 2..30 sec…
Success!
Sending eMMC firmware…
Success!
Verifying eMMC firmware…
Success!
Flashing eMMC firmware…
Success!
Repairing eMMC CID…
Success!
<font color="green">eMMC firmware is updated now! </font>
<font color="green">Please reconnect all eMMC lines before next operation!</font>
<font color="green">Please don’t forget to repair <b>extCSD</b> from backup!</font>
<font color="green">Please don’t forget to configure <b>BOOT</b> sizes!</font>
Done.

Running:Repair extCSD…
Z3X EasyJtag Software ver. 2.3.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1144 mV
CMD Active Level:2237 mV
Box IO Level:2800 mV
CLK Rate:140000 khz
Writing…
Done.

Running:Change BOOT CONFIG…
Z3X EasyJtag Software ver. 2.3.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1144 mV
CMD Active Level:2237 mV
Box IO Level:2800 mV
CLK Rate:140000 khz
Writing eMMC Register…
Written: REG : 179 VAL :48
Done.

Running:Change BOOT WIDTH…
Z3X EasyJtag Software ver. 2.3.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1144 mV
CMD Active Level:2237 mV
Box IO Level:2800 mV
CLK Rate:140000 khz
Writing eMMC Register…
Written: REG : 177 VAL :1
Done.

Z3X EasyJtag Software ver. 2.3.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1144 mV
CMD Active Level:2237 mV
Input file : F:\z3x. Easy Jtag files\Samsung\GT-N8000\Samsung_GT-N8000_XXLGA_16gb_model_dump_rom1_512mb.bin
Writing 0020000000 bytes to 00000000 …ROM1 (USER ROM)
Done. Write Speed: 977 kB/s

STILL DEAD!