Qmobile i7i spd 7731 Reed/Write Flash Done


hi
there is monky virus in Qmobile i7i spd 7731 after flash all is well 😎

Card found: S/N : 2C4288A9 , v0130
Chinese Miracle II [SPD module] v 1.14
Operation : Read FullFlash [ v1.14 ]
1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
3. Insert cable
==== Wait for phone…
Phone found! [ 25 ]
Open Port Failed!
Reconnect Power/Cable!

Operation : Read FullFlash [ v1.14 ]
1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
3. Insert cable
==== Wait for phone…
Phone found! [ 10 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
Boot failed!

Boot failed!
Reconnect Power/Cable!

Operation : Read FullFlash [ v1.14 ]
1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
3. Insert cable
==== Wait for phone…
Device boot not done
Check Drivers
Try again

Reconnect Power/Cable!

Operation : Read FullFlash [ v1.14 ]
1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
3. Insert cable
==== Wait for phone…
Phone found! [ 10 ]
Open Port Failed!
Reconnect Power/Cable!

Operation : Read FullFlash [ v1.14 ]
1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
3. Insert cable
==== Wait for phone…
Phone found! [ 10 ]
Open Port Failed!
Reconnect Power/Cable!

Operation : Read FullFlash [ v1.14 ]
1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
3. Insert cable
==== Wait for phone…
Phone found! [ 10 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SC773x Android 5.x eMMC v1.0 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Step #1 Passed!
[FW_READER] : Step #2 Passed!
[FW_READER] : Step #3 Passed!
Phone found! [ 10 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SC773x Android 5.x eMMC v1.0 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name : QMobile_i7i
Model Brand : Qmobile
Model Device: QMobile_i7i
AndrVersion : 5.1
BaseBand CPU: QMOBILE_I7I
Project Ver : QMobile_i7i_MP_29_10
Model Ext : QMobile i7i
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now …
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x854.bin
[Read Ok] : fblogo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : recovery.img
[Read Ok] : userdata.img
AndroidInfo created
Firmware Size : 1141 MiB
Saved to : C:\Documents and Settings\zeerik\Desktop\i7i backup\QMOBILE_I7I_QMobile_i7i_5.1_QMobile_i7i_MP_ 29_10_QMobile_i7i\
Done!
Elapsed: 00:08:25
Reconnect Power/Cable!

Loading : QMobile_i7i_MP_02_12.pac
CRVersion : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : QMobile_i7i_MP_29_10
FastCheck : 0x4CE099B9
Loading files …
File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : nvitem_wcn.bin
File : u-boot-spl-16k.bin
File : SC7702_sc7731g_band128.bin
File : DSP_DM_G2.bin
File : SC8800G_x30g_wcn_dts_modem.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : LOGO.bmp
File : charge.bmp
File : prodnv.img
File : cache.img
File : u-boot.bin
File : SC7731_UMS.xml
Load Ok!
Operation : Flash [ v1.14 ]
======= Flash
Files set for flashing :
[ MCU ] : QMobile_i7i_MP_02_12.pac
CRVersion : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : QMobile_i7i_MP_29_10
File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : nvitem_wcn.bin
File : u-boot-spl-16k.bin
File : SC7702_sc7731g_band128.bin
File : DSP_DM_G2.bin
File : SC8800G_x30g_wcn_dts_modem.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : LOGO.bmp
File : charge.bmp
File : prodnv.img
File : cache.img
File : u-boot.bin
1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
3. Insert cable
==== Wait for phone…
Phone found! [ 10 ]
Open Port Failed!
Reconnect Power/Cable!

Operation : Flash [ v1.14 ]
======= Flash
Files set for flashing :
[ MCU ] : QMobile_i7i_MP_02_12.pac
CRVersion : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : QMobile_i7i_MP_29_10
File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : nvitem_wcn.bin
File : u-boot-spl-16k.bin
File : SC7702_sc7731g_band128.bin
File : DSP_DM_G2.bin
File : SC8800G_x30g_wcn_dts_modem.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : LOGO.bmp
File : charge.bmp
File : prodnv.img
File : cache.img
File : u-boot.bin
1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
3. Insert cable
==== Wait for phone…
Phone found! [ 10 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
PickUp loaders from pac
Boot failed!
Boot failed!
Reconnect Power/Cable!

Operation : Flash [ v1.14 ]
======= Flash
Files set for flashing :
[ MCU ] : QMobile_i7i_MP_02_12.pac
CRVersion : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : QMobile_i7i_MP_29_10
File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : nvitem_wcn.bin
File : u-boot-spl-16k.bin
File : SC7702_sc7731g_band128.bin
File : DSP_DM_G2.bin
File : SC8800G_x30g_wcn_dts_modem.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : LOGO.bmp
File : charge.bmp
File : prodnv.img
File : cache.img
File : u-boot.bin
1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
3. Insert cable
==== Wait for phone…
Phone found! [ 10 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
PMTManager : Load 0x17 records
PMTManager : PMT Update Ok!
Flashing now
[FlashProc] : ERASE
Current ID : ERASEUBOOT
Current Part : uboot
[FlashProc] : Ok!
[FlashProc] : BOOTCODE
Current ID : SPLLOADER
Current File : u-boot-spl-16k.bin
Flashing now …
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : MODEM_W
Current File : SC7702_sc7731g_band128.bin
Flashing now …
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : DSP_W
Current File : DSP_DM_G2.bin
Flashing now …
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : MODEM_WCN
Current File : SC8800G_x30g_wcn_dts_modem.bin
Flashing now …
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : BOOT
Current File : boot.img
Flashing now …
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : RECOVERY
Current File : recovery.img
Flashing now …
[FlashProc] : Ok!
[FlashProc] : IMAGE
Current ID : SYSTEM
Current File : system.img
Flashing now …
[FlashProc] : Ok!
[FlashProc] : IMAGE
Current ID : USERDATA
Current File : userdata.img
Flashing now …
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : BOOTLOGO
Current File : LOGO.bmp
Flashing now …
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : FASTBOOT_LOGO
Current File : charge.bmp
Flashing now …
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : FLASH
Current Part : wruntimenv1
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : FLASH_WCN
Current Part : wcnruntimenv1
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : PRODNV
Current File : prodnv.img
Flashing now …
[FlashProc] : Ok!
[FlashProc] : IMAGE
Current ID : CACHE
Current File : cache.img
Flashing now …
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : ERASEMISC
Current Part : misc
[FlashProc] : Ok!
[FlashProc] : BOOTCODE
Current ID : UBOOTLOADER
Current File : u-boot.bin
Flashing now …
[FlashProc] : Ok!

Elapsed: 00:03:42
Reconnect Power/Cable!

Related: