Repair Lumia 535 EMMC!

Hello guys/EJ team,

I have a problem repairing Lumia 535 EMMC,
Phone was working fine with the customer until he decided to update it,
After a failure update, phone got stucked at Microsoft logo,
Phone didn’t accept flashing process as it should be,
and it just got bricked and now it’s showing only recovery mode (RED SCREEN),
No matter what i do, it won’t flash with any FW or any Tool,
So, i just made a direct connection on EMMC with EasyJtag in order to repair EMMC,

So, here is the logs:

-This is the first read of EMMC:

Code:

Z3X EasyJtag Software ver. 2.1.0.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: --------------, ,FW Ver.: 01.54
CMD Pullup Level:2031 mV
CMD Active Level:2454 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 1501004B3758564D4201C905D62BB1F2

EMMC CSD : D02701320F5903FFF6DBFFEF8E40400C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 11/2014  Rev.0x1
EMMC NAME: <b>K7XVMB</b> , S/N: 3372602923
EMMC NAME (HEX): 4B3758564D4200
EMMC ROM1 (Main User Data)  Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.7 (MMC 5.0)

Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit  , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]

Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: K7XVMB_3372602923_20160524_1852.extcsd
Done.


-512MB Backup Read:

Code:

Z3X EasyJtag Software ver. 2.1.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2041 mV
CMD Active Level:2650 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
Reading 0x000020000000 bytes from 0x000000000000 ...ROM1 ( USER ROM)
Output file :C:\Users\ZER0\Desktop\EMMC_ROM1_K7XVMB_3372602923_00000000_20000000.bin
Done. Read Speed: 739 kB/s


-EMMC Firmware Update:

Code:

Z3X EasyJtag Software ver. 2.1.0.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: --------------, ,FW Ver.: 01.54
CMD Pullup Level:2052 mV
CMD Active Level:2640 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!
Success!
<font color="green">eMMC firmware is updated now! </font>
<font color="green">Please reconnect all eMMC lines before next operation!</font>
<font color="green">Please don't forget to repair <b>extCSD</b> from backup!</font>
<font color="green">Please don't forget to configure <b>BOOT</b> sizes!</font>
Done.


-512MB USER ROM Write:

Code:

Z3X EasyJtag Software ver. 2.1.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2021 mV
CMD Active Level:2371 mV
Input file : C:\Users\ZER0\Desktop\Nokia_Lumia_535_emmc_direct_dump\Nokia_Lumia_535_emmc_direct_dump\EMMC_ROM1_00000000_20000000.bin
Writing 0020000000 bytes to 00000000 ...ROM1 (USER ROM)
Done. Write Speed: 614 kB/s


-BOOT1 ROM Write:

Code:

Z3X EasyJtag Software ver. 2.1.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2021 mV
CMD Active Level:2371 mV
Input file : C:\Users\ZER0\Desktop\Nokia_Lumia_535_emmc_direct_dump\Nokia_Lumia_535_emmc_direct_dump\EMMC_ROM2_00000000_00400000.bin
Writing 0000400000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 1364 kB/s


-BOOT2 ROM Write:

Code:

Z3X EasyJtag Software ver. 2.1.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2021 mV
CMD Active Level:2371 mV
Input file : C:\Users\ZER0\Desktop\Nokia_Lumia_535_emmc_direct_dump\Nokia_Lumia_535_emmc_direct_dump\EMMC_ROM3_00000000_00400000.bin
Writing 0000400000 bytes to 00000000 ...ROM3 (BOOT2 ROM)
Done. Write Speed: 1351 kB/s


-EMMC Read After Process:

Code:


Z3X EasyJtag Software ver. 2.1.0.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: -------------, ,FW Ver.: 01.54
CMD Pullup Level:2041 mV
CMD Active Level:2650 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 1501004B3758564D30012400D829712A

EMMC CSD : D02701320F5903FFF6DBFFEF8E40400C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2014  Rev.0x1
EMMC NAME: <b>K7XVM0</b> , S/N:  604035113
EMMC NAME (HEX): 4B3758564D3000
EMMC ROM1 (Main User Data)  Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
  Extended CSD rev 1.7 (MMC 5.0)

Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit  , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]

Partitioning Support [PARTITIONING_SUPPORT]: 0x07

 Device support partitioning feature

 Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

Backup saved: K7XVM0_ 604035113_20160524_1945.extcsd
Done.


After that i tried to reflash the phone again with a full charged battery,
And the flashing process got stuck and the phone got bricked with the recovery mode again,
So, what am i doing wrong!!,
if someone can help in this, that’d be much appreciated,
Thanks in advance