where no one can , infinity rocks !!

proudly infinity box user since 2006

lg h320mb

phone completly dead , only recognized by pc on preloader mode

analizing posibilities

octopus box , only support flashing from full reading , but this phone have security damaged after bad flashing , then octopus cannot flash this phone

z3x only support flashing this model by download interface on kdz format , then not possible , cause this phone dont have avalible download mode ( emergency mode )

after look for full factory reading flash in scatter format , and flash with infinity box , phone recovers download mode and power on again but frezze on logo screen , maybe nv data corrupted

after found same phone model , and reading in full raw bin format , again flash the phone now with BIN format , and after this phone power on and becomes fully functional

WHERE

NCK , VOLCANO , CSTOOL , AVENGERS , FALCON , SPFLASHTOOL , MIRACLE BOX FAILS INFINITY ROCKS AGAIN

Quote:

Card found : S/N : 271C324A , v0134
Chinese Miracle II [MTK module] v 1.58

Operation : Check / Read Info [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 112 ]
Sync…
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA …
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D4200541756005259
Initialize Memory …
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D4200541756005259
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x5F4A065816AB9BF9C33E96B41146FCDA
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : lge
ProdName : my50_global_com
ProdModel : LG-H320
Device : my50
AndroidVer: 5.0.1
SWVersion : LGH320AT-00-V10a-GLOBAL-COM-APR-13-2015+1
CU_SWVer : H32010a
MTKxCPU : MT6582
MTKxPRJ : ALPS.L0.MP1.TC1SP.V1.4_MUSE6582.Y50.L_TMP2

SECURITY :
BTMAC Addr : E6F34141823D
WiFi MAC : 000000000000

MODEM :
BaseBand : MT6582_S00_MOLY_WR8_W1338_MD_WG_TC01_MUSE82Y_SP_V1 _1_wg_n

EXTRA :
LCD [0] : db7436_dsi_vdo_fwvga
LCD Res : 854×480
TOUCH [0] : GT9XX
CAM [0] : ov8858_mipi_raw
CAM [1] : imx219_mipi_raw
CAM [2] : hi544_mipi_raw
CAM [3] : hi707_yuv
MODEM : my50_hspa
LOCALE : en_US zh_CN zh_TW es_ES pt_BR ru_RU fr_FR de_DE tr_TR vi_VN ms_MY in_ID th_TH it_IT ar_EG hi_IN bn_IN ur_PK fa_IR pt_PT nl_NL el_GR hu_HU tl_PH ro_RO cs_CZ ko_KR km_KH iw_IL my_MM pl_PL es_US bg_BG hr_HR lv_LV lt_LT sk_SK uk_UA de_AT da_DK fi_FI nb_NO sv_SE en_GB hy_AM zh_HK et_EE ja_JP kk_KZ sr_RS sl_SI ca_ES

Done!
Elapsed: 00:00:10
Reconnect Power/Cable!

Operation : Read Flash [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 112 ]
Sync…
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA …
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D4200541756005259
Initialize Memory …
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D4200541756005259
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x5F4A065816AB9BF9C33E96B41146FCDA
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Content now …

Read Ok , collect info
Brand : lge
ProdName : my50_global_com
ProdModel : LG-H320
Device : my50
AndroidVer: 5.0.1
MTKxCPU : MT6582
MTKxPRJ : ALPS.L0.MP1.TC1SP.V1.4_MUSE6582.Y50.L_TMP2
Saved to : C:\Users\Regelio\Desktop\lg leonh320mb\BIN format\MT6582__LGE__LG-H320__my50_global_com__my50__ALPS.L0.MP1.TC1SP.V1. 4_MUSE6582.Y50.L_TMP2__Android_5.0.1.ispff

Done!
Elapsed: 00:28:36
Reconnect Power/Cable!

Operation : Read Flash [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 112 ]
Sync…
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA …
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D4200541756005259
Initialize Memory …
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D4200541756005259
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x5F4A065816AB9BF9C33E96B41146FCDA
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Content now …

Brand : lge
ProdName : my50_global_com
ProdModel : LG-H320
Device : my50
AndroidVer: 5.0.1
SWVersion : LGH320AT-00-V10a-GLOBAL-COM-APR-13-2015+1
CU_SWVer : H32010a
MTKxCPU : MT6582
MTKxPRJ : ALPS.L0.MP1.TC1SP.V1.4_MUSE6582.Y50.L_TMP2

[Read Ok] : preloader_muse6582_y50_l.bin
[Read Ok] : MBR
[Read Ok] : EBR1
[Read Ok] : lk.bin
[Read Ok] : laf.img
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : EBR2
[Read Ok] : EBR3
[Read Ok] : persist.img
[Read Ok] : cust.img
[Read Ok] : factory.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img

[ScatCFG] : MT6582 / V1.1.1 / muse6582_y50_l / EMMC
Android Info saved
FW Size : 2010 MiB
Scatter saved to : C:\Users\Regelio\Desktop\lg leonh320mb\factory format\MT6582__lge__LG-H320__my50__5.0.1__LGH320AT-00-V10a-GLOBAL-COM-APR-13-2015+1\

All done!

Done!
Elapsed: 00:14:21
Reconnect Power/Cable!

Scatter Load Ok , BaseBand : MT6582 , Project : muse6582_y50_l , Storage : EMMC
Files found : 17 , Set to Flash : 16
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : lge
Device Model : my50
Device CPU : MT6582
Device IntName : my50_global_com
Device Version : 5.0.1
SWVersion : LGH320AT-00-V10a-GLOBAL-COM-APR-13-2015+1
CU_SWVer : H32010a
Device Compile : 13/04/2015 01:26:58 p.m.
Device Project : ALPS.L0.MP1.TC1SP.V1.4_MUSE6582.Y50.L_TMP2
Device ExtInfo : LG-H320
Ready to Flash!

Operation : Flash [ v1.58 ]

======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 112 ]
Sync…
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA …
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D420044C8E07A5243
Initialize Memory …
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D420044C8E07A5243
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x5F4A0658E866020709C6E7FDE28A4E16
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ScatCFG : BaseBand : MT6582 , Project : muse6582_y50_l , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled

BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!

BL : BatteryLevel : 4167 mV
BL : BatteryLevel Ok

BL : Flash Pre-Erase
Total blocks to Erase : 4
Erase : 0x0000000000C00000-0x0000000000100000
Erase : 0x0000000003900000-0x0000000004900000
Erase : 0x0000000008280000-0x0000000002480000
Erase : 0x000000000AB00000-0x00000001C5500000
Flash Pre-Erase Done, time used : 00:00:04

SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader …
Use : preloader_muse6582_y50_l.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0024
Update PMT by user request
Repartition Done!
Use FLN Mode

Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : LAF
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : EBR2
Image Flash Ok
Flash now : EBR3
Image Flash Ok
Flash now : PERSIST
Image Flash Ok
Flash now : CUST
Image Flash Ok
Flash now : FACTORY
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:08:13

Processing : Verify
Verify Passed : MBR
Verify Passed : EBR1
Verify Passed : UBOOT
Verify Passed : LAF
Verify Passed : BOOTIMG
Verify Passed : RECOVERY
Verify Passed : SEC_RO
Verify Passed : LOGO
Verify Passed : EBR2
Verify Passed : EBR3
Verify Passed : PERSIST
Verify Passed : CUST
Verify Passed : FACTORY
Verify Passed : ANDROID
Verify Passed : CACHE
Verify Passed : USRDATA
Data Verify Done, time used : 00:01:17

Update Mirror PMT
Update Done!

Update RomInfo done

Done!
Elapsed: 00:09:49
Reconnect Power/Cable!

Load File
File_Info : muse6582_y50_l
FileVersion : MT6582
Load File Ok

Operation : Read NVRAM [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 112 ]
Sync…
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA …
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D420044C8E07A5243
Initialize Memory …
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D420044C8E07A5243
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x5F4A0658E866020709C6E7FDE28A4E16
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[Info] : BaseBand : MT6582_S00_MOLY_WR8_W1338_MD_WG_TC01_MUSE82Y_SP_V1 _1_wg_n

NVM Read Ok, MT6582_S00_MOLY_WR8_W1338_MD_WG_TC01_MUSE82Y_SP_V1 _1_wg_n_eMMC.spnv
SEC Read Ok, LG-H320mb_CB42S150610005866.lgsec

Done!
Elapsed: 00:00:31
Reconnect Power/Cable!

Operation : Flash [ v1.58 ]

======= Flash
Files set for flashing :
[ MCU ] : MT6582__LGE__LG-H320__my50_global_com__my50__ALPS.L0.MP1.TC1SP.V1. 4_MUSE6582.Y50.L_TMP2__Android_5.0.1.ispff

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 112 ]
Sync…
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA …
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D420044C8E07A5243
Initialize Memory …
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D420044C8E07A5243
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x5F4A0658E866020709C6E7FDE28A4E16
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

ISPFF ID : 6582 , TARGET ID : 6582

Flash pre-erase enabled
Erase Flash now …
Flash pre-erase done

Write Flash now …
[ MCU ] : MT6582__LGE__LG-H320__my50_global_com__my50__ALPS.L0.MP1.TC1SP.V1. 4_MUSE6582.Y50.L_TMP2__Android_5.0.1.ispff

Init Ok , Sending blocks …
Write done , 7456 blocks sent

Done!
Elapsed: 00:22:12
Reconnect Power/Cable!

Operation : SP Unlock [ v1.58 ]
Mode : Read Codes

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 112 ]
Sync…
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA …
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D420044C8E07A5243
Initialize Memory …
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D420044C8E07A5243
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x5F4A0658E866020709C6E7FDE28A4E16
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

UNCK : 4330798475153978
USIM : 5408206481880540
NSCK : 1740761381929603
SPCK : 7491762054951381
UCCK : 2435794892267082
UHCK : 0000000000000000

Done!
Elapsed: 00:00:25
Reconnect Power/Cable!