Samsung G531F Dead boot Repair Done With Easy jtag.

Samsung G531F Dead boot Repair Done With Easy jtag.

Quote:

Z3X EasyJtag Software ver. 2.6.0.1
Loading eMMC GEN1 Firmware… IO: 3300 mV
Box S/N: ———–, ,FW Ver.: 01.60
CMD Pullup Level:2918 mV
CMD Active Level:3155 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is ON!
———- eMMC Device Information ———-

EMMC CID : 90014A4838473474210105356C67C288

EMMC CSD : D07F01320F5903FFFFFFFFEF8A400012

EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 12/2015 Rev.0x1
EMMC NAME: H8G4t , S/N: 87387239
EMMC NAME (HEX): 48384734742000
Can’t init EMMC, Reason: DATA RCV CRC Error
Check Data Line!
Done.

Z3X EasyJtag Software ver. 2.6.0.1
Loading eMMC GEN1 Firmware… IO: 2800 mV
Box S/N: 1616FF0EE7DE8EC3, ,FW Ver.: 01.60
CMD Pullup Level:2908 mV
CMD Active Level:2784 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower mode is ON!
———- eMMC Device Information ———-

EMMC CID : 90014A4838473474210105356C67C288

EMMC CSD : D07F01320F5903FFFFFFFFEF8A400012

EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 12/2015 Rev.0x1
EMMC NAME: H8G4t , S/N: 87387239
EMMC NAME (HEX): 48384734742000
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.7 (MMC 5.0)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]

Partitioning Support [PARTITIONING_SUPPORT]: 0x07

Device support partitioning feature

Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

———————————————

Backup saved: H8G4t _ 87387239_20170724_1007.extcsd
mmc_read_blocks(0xE8FFFF , 1 ), Reason: DATA RCV CRC Error
Done.

Running:Repair extCSD…
Z3X EasyJtag Software ver. 2.6.0.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:2908 mV
CMD Active Level:2784 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
————Parsing extCSD————
=============================================

Extended CSD rev 1.6 (MMC 4.5)

=============================================

Card Supported Command sets [S_CMD_SET: 0x01]

HPI Features [HPI_FEATURE: 0x03]:
implementation based on CMD12

Background operations support [BKOPS_SUPPORT: 0x01]

Max Packet Read Cmd [MAX_PACKED_READS: 0x3c]

Max Packet Write Cmd [MAX_PACKED_WRITES: 0x20]

Data TAG support [DATA_TAG_SUPPORT: 0x01]

Data TAG Unit Size [TAG_UNIT_SIZE: 0x03]

Tag Resources Size [TAG_RES_SIZE: 0x00]

Context Management Capabilities [CONTEXT_CAPABILITIES: 0x05]

Large Unit Size [LARGE_UNIT_SIZE_M1: 0x07]

Extended partition attribute support [EXT_SUPPORT: 0x03]

Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x19]

Power off notification [POWER_OFF_LONG_TIME: 0xff]

Cache Size [CACHE_SIZE] is 256 KiB

Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x19]

Power off notification [POWER_OFF_LONG_TIME: 0xff]

Cache Size [CACHE_SIZE] is 256 KiB

Background operations status [BKOPS_STATUS: 0x00]

1st Initialisation Time after programmed sector [INI_TIMEOUT_AP: 0x32]

Power class for 52MHz, DDR at 3.6V [PWR_CL_DDR_52_360: 0x04]

Power class for 52MHz, DDR at 1.95V [PWR_CL_DDR_52_195: 0x09]

Power class for 200MHz at 3.6V [PWR_CL_200_360: 0x09]

Power class for 200MHz, at 1.95V [PWR_CL_200_195: 0x00]

Minimum Performance for 8bit at 52MHz in DDR mode:

[MIN_PERF_DDR_W_8_52: 0x00]

[MIN_PERF_DDR_R_8_52: 0x00]

TRIM Multiplier [TRIM_MULT: 0x03]

Secure Feature support [SEC_FEATURE_SUPPORT: 0x55]

Boot Information [BOOT_INFO: 0x07]

Device supports alternative boot method

Device supports dual data rate during boot

Device supports high speed timing during boot

Boot partition size [BOOT_SIZE_MULTI: 0x20]

Access size [ACC_SIZE: 0x07]

High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x10]

High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]

Reliable write sector count [REL_WR_SEC_C: 0x01]

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x01]

Sleep current (VCC) [S_C_VCC: 0x06]

Sleep current (VCCQ) [S_C_VCCQ: 0x0a]

Sleep/awake timeout [S_A_TIMEOUT: 0x10]

Sector Count [SEC_COUNT: 0x00e90000]

Minimum Write Performance for 8bit:

[MIN_PERF_W_8_52: 0x08]

[MIN_PERF_R_8_52: 0x08]

[MIN_PERF_W_8_26_4_52: 0x08]

[MIN_PERF_R_8_26_4_52: 0x08]

Minimum Write Performance for 4bit:

[MIN_PERF_W_4_26: 0x08]

[MIN_PERF_R_4_26: 0x08]

Power classes registers:

[PWR_CL_26_360: 0x02]

[PWR_CL_52_360: 0x02]

[PWR_CL_26_195: 0x05]

[PWR_CL_52_195: 0x05]

Partition switching timing [PARTITION_SWITCH_TIME: 0x03]

Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x0a]

I/O Driver Strength [DRIVER_STRENGTH: 0x0f]

Card Type [CARD_TYPE: 0x17]

CSD structure version [CSD_STRUCTURE: 0x02]

Command set [CMD_SET: 0x00]

Command set revision [CMD_SET_REV: 0x00]

Power class [POWER_CLASS: 0x00]

High-speed interface timing [HS_TIMING: 0x00]

Erased memory content [ERASED_MEM_CONT: 0x00]

Boot configuration bytes [PARTITION_CONFIG: 0x48]

No access to boot partition

Boot config protection [BOOT_CONFIG_PROT: 0x00]

Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x01]

High-density erase group definition [ERASE_GROUP_DEF: 0x00]

Boot write protection status registers [BOOT_WP_STATUS]: 0x00

Boot Area Write protection [BOOT_WP]: 0x00

Power ReadOnly locking: possible

Permanent ReadOnly locking: possible

Read Only lock status: not locked

User area write protection register [USER_WP]: 0x00

FW configuration [FW_CONFIG]: 0x00

RPMB Size [RPMB_SIZE_MULT]: 0x20

Write reliability setting register [WR_REL_SET]: 0x1f

Write reliability parameter register [WR_REL_PARAM]: 0x05

Enable background operations handshake [BKOPS_EN]: 0x00

H/W reset function [RST_N_FUNCTION]: 0x00

HPI management [HPI_MGMT]: 0x00

Partitioning Support [PARTITIONING_SUPPORT]: 0x07

Device support partitioning feature

Device can have enhanced tech.

Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0x0001d2

Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00


BR
Qaisar Mahmood